Westinghouse 7787100 Manuel d'utilisation et d'entretien télécharger pdf

WARNINGS:

•

To avoid fire, shock, and serious personal injury, follow all

instructions carefully. Read and save these instructions for

future reference.

•

Do not install or use this unit if any part is damaged or miss-

ing.

•

IMPORTANT!

Fan installation must be complete, including the

assembly of blades, before testing the remote control unit.

NOTICE:

1. This remote is designed for both CFL lamp and Incandescent

Lamp.

SAFETY PRECAUTIONS:

2. This remote control is rated for a maximum (ceiling fan only) motor amp

of 0.80 at 120 volts, total (incandescent bulb only) wattage equaling 300

watt maximum.

3. Do not use with solid state ceiling fans.

4. The decorative housing (canopy) at the ceiling must be metal.

The metal housing acts as a protective cover for the Control Unit.

DO NOT USE WITH A NON-METALLIC HOUSING.

5. Only the remote unit should be used to change fan speeds. Do not use

the pull chain to change fan speeds after installation.

6. Make sure no bare wires are exposed outside of the connectors.

7. All wiring must conform to national and local electrical codes. If you

feel that you do not have enough electrical wiring knowledge or experi-

ence, have your fan control installed by a licensed electrician.

Any

electrical work not described in this manual should be performed

by a licensed electrician.

8. Do not use water or detergents to clean the remote transmitter unit. A

dry dust cloth will be suitable for most cleaning.

9. Use of this control with some ceiling fans could result in fire, shock,

and serious personal injury. Use this fan control with capacitor

speed controlled ceiling fans only.

B. INSTRUCTIONS FOR YOUR NEW WESTINGHOUSE REMOTE FAN CONTROL SYSTEM

WARNING: HIGH VOLTAGE

Before connecting this control unit:

• Disconnect electrical power from the circuit to be used.

• Household power can cause serious injury or death.

• Wiring must meet all local electrical code requirements.

FIGURE 7

TRANSMITTER

(BACK OF REMOTE)

FIGURE 6

A. MAKING THE ELECTRICAL CONNECTIONS:

NOTE: This remote only works

with some fans that are installed

in sloped ceilings.

Do not use fan speed control in

canopies where the mounting is

not as described in figures 4 or 5.

This remote cannot be installed in a

downrod style fan when in flushmount

mode (when downrod is not in use).

1. Disconnect existing wiring between ceiling fan and AC sup-

ply at electrical junction box.

FOR FANS ON A DOWNROD:

Remove ceiling fan canopy

from its mounting plate. (See figure 4.)

FOR FLUSHMOUNT FANS:

Remove decorative housing

from mounting plate (see figure 2). Disconnect mounting

bracket from mounting plate and allow to hang from one side

(see figure 3).

3. Making the electrical connection:

• Connect GREEN fan wire to BARE (ground) wire.

• Connect BLACK control unit wire to BLACK supply wire

(AC L).

• Connect WHITE control unit wire to WHITE supply wire

(AC N).

• Connect WHITE control unit wire (MOTOR N) to WHITE

fan wire.

• Push the connected wires up into the junction box.

Place

BLACK wires on one side of box, and WHITE, GREEN

and

BARE (ground) wires on the other side of the box.

•

Connect RED control unit wire (MOTOR L) to BLACK fan wire.

• Connect BLUE control unit wire (FOR LIGHT) to BLUE

light wire.

• Push the connected wires up into the junction box.

• Lay the BLACK control unit wire (ANTENNA) on top of the

control unit.

•

FOR FANS ON A DOWNROD:

Lay the control unit in the

canopy (see figure 4). Reinstall the canopy on its mount-

ing plate. Restore electrical power to the circuit.

• FOR FLUSHMOUNT FANS:

Attach the control unit to

the mounting plate or to the ceiling with the supplied tie

wraps (see figure 5). Reconnect the mounting bracket to

the mounting plate (see figure 2). Reinstall the decorative

housing on its mounting plate. Restore electrical power to

the circuit.

NOTE: If the unit does not fit properly between the

mounting plate and ceiling, attach the u

nit to the

underside of the mounting plate.

BLACK BLACK

BLUE

RED BLACK

WHITE WHITE

BLUE

CONTROL

UNIT

LIGHT

FAN

AC SUPPLY

WHITE WHITE

AC SUPPLY

BARE (GROUND) GREEN FAN

AC SUPPLY

FIGURE 1

FIGURE - 2

FLUSHMOUNT FANS ONLY

FIGURE - 3

FLUSHMOUNT FANS ONLY

CONTROL

UNIT

FIGURE - 4

DOWNROD FANS ONLY

CEILING

JUNCTION BOX

MOUNTING PLATE

CONTROL UNIT

FIGURE - 5

FLUSHMOUNT FANS ONLY

TROUBLESHOOTING GUIDE

PROBLEM: REMOTE FAILS TO OPERATE

Check:

• Is there power to the control unit?

• Is the control unit wired correctly?

• Are the fan and light switches set on the highest position?

• Is there a good battery in the remote? If the red indicator lights when either

button is pushed, the battery is good.

•

Are the switches set the same in both the remote and the control unit?

PROBLEM: SHORT RANGE

Solution:

•

If the remote can operate the control unit when close to it but does not oper-

ate it at distances of 30-50 feet, try placing the black antenna wire above the

ceiling and outside of the junction box.

LIMITED WARRANTY

The Westinghouse remote control for ceiling fans offers a limited war-

ranty of one year from the date of purchase to the original owner against

defects in material and workmanship. All spare parts are covered for

ninety days only. This warranty is in

lieu of all other warranties expressed or

implied.

Westinghouse will repair or replace this remote control if it is defec-

tive due to faulty materials or workmanship. This warranty does not cover

service charges, batteries, defects resulting from accidents, damages caused

through abuse or alterations or by affixing any attachment not provided with

the product, improper installation or maintenance, failure of supporting

devices not supplied as original mounting hardware, exposures to extremes

of heat or humidity, incorrect voltage, surges in current,

unauthorized repair, or failures caused by modifications of the product or the

acts of third parties. See remote manual for proper installation.

If a warranty claim is made in the first year, simply return the remote with

a copy of the original sales receipt, freight prepaid to Westinghouse Lighting

Corporation, who, at its option, shall repair or replace the remote or refund

the purchase price.

Please pack product correctly to eliminate shipping

damage.

Send all remotes and inquiries to:

Westinghouse Lighting

Attn: Customer Service

12401 McNulty Road

Philadelphia, PA 19154-1029

If you have

any questions regarding the installation of this item or the

warranty coverage, please call our consumer line at

1-888-417-6222

and a

representative will assist you.

77871

Installation & Operating Instructions for the

Westinghouse Ceiling Fan and Light Remote Control

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com

Please open the back cover

of the remote transmitter,

and find the blue toggle

switch. It is preset at "1" for

non-dimmable lamp like CFL

or LED. If you're planning to

use Incandescent Lamp,

Slide up the toggle switch at

"ON" to active light dimmer

function.

TOGGLE SWITCH

Remote control setting and speed control setting process:

All remote controls will be preset up a pair of codes when being manufactured. After

installing the unit and restoring power to your fan, press and hold the “OFF” button for

5 seconds. You must press the “OFF” button within 60 seconds of restoring power to

the fan. The speed setting process is completed after hearing 4 short beep sounds.

The remote buttons function as follows:

1. High speed – When you press the “Hi” key, it will emit 3 long beep sounds indicating the fan is starting up;

Med speed – When you press the “MED” key, it will emit 2 long beep sounds indicating the fan is starting up;

Low speed – When you press the “LO” key, it will emit 1 long beep sound indicating the fan is starting up;

Fan off – When you press the “OFF” key, it will emit 4 short beep sounds indicating the fan is turning off;

2. Light On/Off – When you press the “LIGHT” key, it will emit only 1 short beep sound indicating when the

light is turned on or off.

3. Light Dimmer – When the toggle switch is set at "ON" position, continuous pressure on the light button

dims light in a continuous cycle from light to dark, or dark to light. It will emit 2 short beep sounds indicating

the dimming level.

OFF

MED

1 2 3

Résumé du contenu

Page 1 - SAFETY PRECAUTIONS:

WARNINGS:• To avoid fire, shock, and serious personal injury, follow all instructions carefully. Read and save these instructions for

Page 2 - PRECAUCIONES DE SEGURIDAD:

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trade

Page 3 - MESURES DE PRÉCAUTION:

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trade

Commentaires sur ces manuels

Pas de commentaire

Westinghouse 7787100 Manuel d'utilisation et d'entretien

Naviguer en ligne ou télécharger Manuel d'utilisation et d'entretien pour Ventilateurs des ménages Westinghouse 7787100. Westinghouse 7787100 Use and Care Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Ventilateurs des ménages Westinghouse 7787100